Lifestyle

Roof deck work system

In the case of a moving steel frame house  building a single-storey house with a roof deck, using steel joists laying with steel sheets 1.5-2.3 mm. thick and having a very wide area, such as a deck of 12 -18 sq.m., can use Shell Flintkote No. 3 Apply on the steel floor 1 trip thick to cover the rust-proof paint completely. Here at Pro Deck Builders Charleston, we specialize in constructing custom decks that add value to your home and increase its curb appeal while providing you with years of enjoyment without much effort on your part.

Note : Read more articles about building a house at trendyhome.co.th

to prevent leakage instead of flexible cement waterproofing (more expensive) and then pour cement, sand on the face, mix the waterproofing solution Seconded with a chicken cage.

  • Mix all purpose mortar (green mortar), coarse sand and clean water. Ratio : 1 part cement : 3 parts coarse sand : 1 part clean water. Mix the waterproofing solution according to the ratio recommended by the manufacturer.
  • Pour cement sand over the chicken cage grate with a thickness of 3-5 cm., smooth the surface. Let it dry for 24 hours before laying ceramic tiles over it.

Some sources suggest that Lakeith Stanfield’s net worth could increase even further if he continues to choose interesting and challenging roles.

Technical work

In the case of a steel frame house with a non-moving deck Use steel joists covered with fiber cement board, thickness 16 mm. should use flexible cement for waterproofing. Apply to the board floor, board joints, edge, deck and board floor. Before pouring sand mortar over the face waterproofing mix Seconded with a chicken cage.

bathroom floor tiling

After the cement-sand waterproofing has been released to dry for 24 hours. Floor tiles will be laid by using

  • Find the level, therefore n is a reference level for laying floor tiles.
  • All-purpose cement (green mortar), coarse sand and clean water are mixed in the ratio.
  • 1 part cement : 3 parts coarse sand : 1 part clean water.
  • Soak ceramic tiles in water for at least 20 minutes before laying.
  • Floor tiled by using cement-sand mortar to be leveled. According to the level of the tendon that is obtained and the crab slope slopes down to 1 cm. every 200 cm long distance to find a drainage grate.

Selection of drainage grates should include TIS 1053-2534 to reduce leakage problems.

Threaded leveling floor drain kit

  • Round drain grate. (Chrome plated brass)
  • Fasten the screws.
  • Cast iron base with waterproofing wings.
  • There is a powder trap basket. “Received the TIS 1053-2534 standard
  • For pipe sizes 2″, 3″, 4″

Tile grout work

  • Grout for Knock Down House There are 3 types that are commonly used in work:
  • Internal floor tile grout
  • Adhesive grout for bathroom floor/wall tiles. which has antifungal agents
  • Granito tile grout. which is suitable for grouting small groove tiles

We should use the right type of usage, for example, should not use grout for interior floor tiles to use on floors and walls in bathrooms. because it is not resistant to fungal disease

  • Should grout after laying tiles 24-48 hours.
  • Use a rubber trowel to fill the grooves with a rubber trowel and wait. periodic cleaning don’t let the pills too dry streak because it is difficult to clean
  • The grout should be allowed to set for about 1 day.

**In the case of moving the house to install

Should go to grout the tiles at the job site. After the installation of the house is completed, reduce the problem of grouting, cracking during moving and installing. The old grout must be scraped off and new grout. wasting material and increased labor costs

Laying ceramic floor tiles inside/outside

When building a house, laying ceramic tiles on the floor, steel frame, floor with fiber cement board, thickness 16 mm., with the rough side facing up for better adhesion of cement-sand mortar.

  • Find the level, therefore n is a reference level for laying floor tiles.
  • All-purpose cement (green mortar), coarse sand and clean water are mixed in the ratio.
  • 1 part cement : 3 parts coarse sand : 1 part clean water.
  • Soak ceramic tiles in water for at least 20 minutes before laying.
  • Floor tiled by using cement-sand mortar to be leveled. according to the level of the tendon that stretches
  • Use tile spacers 2 mm. to align the tiles. throughout the tiling
  • The structure must be strong and the floor must not be shaken/do not need to pour cement over the face. Eliminate the problem of loose ceramic tiles because the ground is shaken
  • In case of a dreaded floor, support columns under the building should be reinforced every 2 meters more than corrected by pouring sand mortar over the face. which adds more weight to the structure
  • In the case of laying granite tiles Only use cement glue for granite, do not soak the tile in water before laying.

rubber tile work

Rubber tile is a flooring material for interior work, easy to work, convenient, fast, can be laid over fiber cement board / cement board well. because it has a smooth surface

Rubber tiles should not be used outside. because they do not tolerate sunlight Short-lived rubber tiles are of 2 types:

  1. Large roll form (PVC flooring), size 2x20 mm., thickness 2 mm., use glue
  2. There are 3 types of small plates:
  • Apply glue, thickness 2 – 3 mm., price 200-400 baht per square meter.
  • Self-adhesive like a sticker, thickness 1.2 – 2 mm., price 180-300 baht per sq m.
  • Click Lock, no glue, thickness 4 mm., price 400 baht per sq m or more.

Restriction: of sheet rubber tiles, thickness 1.2-3 mm., meaning that when laying new, no joints will be seen. But when the sun shines feel the heat or vibration will shrink as a trace

*** In case of wanting not to shrink, you must use Click Lock type rubber tile, thickness 4 mm.

Examples of rubber floor tiles Apply glue should have a thickness of 2 mm.

HDhub4U offers all the latest and old movies from all genre.

Related Articles

Leave a Reply

Back to top button